Home   Up a Level   Store Top   Terms & Conds   Search   Contact Us   Login

Basic Electric Roller Blind Kits

Online Catalogue | Electric Roller Blind Kits | Low Voltage (24v DC Electric Roller Blind Kits) |  Basic Electric Roller Blind Kits

Ordering Notice
International Orders:
Electric Blinds Online is unable to accept international orders, we will ship and invoice only to United Kingdom addresses.

Ordering Notice:
Due to Intelli-Blinds moving to new premises there will be disruption and extended delivery times for products ordered on our Electric Blinds Online site. We expect disruption to extend into February.
Basic Electric Roller Blind Kit
Intelli-Blinds Basic Roller Kit is a perfect solution to DIY your own electric roller blinds. All our kits are easily adjusted to your window width and include everything to get you going.

Please note: The Basic kit does not include any electronics or controls, therefore you will need understanding of switching and control methods for low voltage DC motors or use of 3rd party controls designed to operate low voltage DC motors. If you are unsure please see our Somfy or Control-IT Kits which include controls.
Whats Included
The kit includes all you need to convert an existing or make a new roller blind motorised:

Intelli-Blinds 28mm motor, Intelli-Blinds PT-24 power supply, 29mm extruded aluminium tube, end pin and brackets, bottom rail and full instructions.
Because our basic kits do not include controls this allows you to directly connect and control them from your own or compatible home or building automation system. Most automation systems have options for relay outputs to allow the control of motors.

You will need to connect the PSU and Motor to a suitable relay setup, this could be directly onto KNX blind control actuators, Crestron, Lutron, Rako etc volt-free relay outputs or maybe your own DIY project using Microcontrollers etc. The motor is simply controlled by changing the polarity of the 24V DC supplied by the PSU. In technical terms the switch or relay arrangement you need would be a 'Double Pole, Double Throw Changeover'.
Control Method
Fabrics
If you require fabric covers for your roller we can offer three basic fabric options when ordering your kits. This high quality German made Trevira fabric available in mid-grey & beige blackout or beige.

This is supplied as a 2000mm wide by 2200mm pre-squared roll separate from the kit, it will need to be cut down on one side to your desired width and mounted to the roller tube. The tube is supplied mounted with double-sided tape to facilitate this.
Fabrics
Installation
The roller tube can be cut to size with just a junior hacksaw to make a blind from 500mm to 2000mm wide.

Note that depending on the location of your nearest power socket & placement of the your relays you may need to purchase additional cable. The cable lengths of the PSU are 1.2m and the motor includes 0.9m cable.

Download the Installation & User Guide.
Custom Made Size
We can manufacture your kits to a custom size if you do not feel confident to cut down the roller tube or cut the fabric to size we can do it for you. We will cut the roller tube and fabric to size, mount onto the roller and fully test the blind.

The measurement shown below in the ordering section allows you to choose a width between 500 and 2000mm. This is the final complete blind width in millimeters including the brackets. To work out what size you'll need for your window simply measure the reveal and take off 5mm and select the nearest size. So for example if your window reveal is 1342mm wide you should select the 1335 size. Typically a finished blind is around 5-15mm less than the reveal. Note to take into account any obstruction in the window eg skirting boards, dado rails etc.

You should also check measure the window at the top and bottom as window reveals are rarely square, if your window does taper then you should use the smaller of the sizes.

If you also choose to order optional fabric, it will also be cut to the appropriate size and mounted onto the tube for you.
Single Basic Roller Kit (RK006)Single Basic Roller Kit (RK006)
Single electric 500 to 2000mm roller blind kit with no controls.
Price: £114.05 (Including VAT at 20%)


Select Fabric (+£60.00 Including VAT)



Custom Made Size (No Charge)

Select finished blind size in mm (including brackets).


Quantity:  

Dual Basic Roller Kit (RK007)Dual Basic Roller Kit (RK007)
Dual electric 500 to 2000mm roller blind kit with no controls.
Price: £205.15 (Including VAT at 20%)


Select Fabric Blind 1 (+£60.00 Including VAT)



Custom Made Size Blind 1 (No Charge)

Select finished blind size in mm (including brackets).


Select Fabric Blind 2 (+£60.00 Including VAT)



Custom Made Size Blind 2 (No Charge)

Select finished blind size in mm (including brackets).


Quantity:  

Online Catalogue | Electric Roller Blind Kits | Low Voltage (24v DC Electric Roller Blind Kits) |  Basic Electric Roller Blind Kits

View Cart
Checkout